Plugwise
This enables Plugwise
Platforms available - depending on your Smile and setup include:
-
climate
(for the stand-alone Anna, for Adam, a climate entity is shown for each zone containing devices like an Anna or another type of wired-thermostat, Jip or Lisa combined with one or more Tom/Floor devices) -
binary_sensor
(for showing the status of e.g. domestic hot water heating or secondary heater) -
button
(for the Adam and the non-legacy Anna and P1 gateways) -
number
(for changing a boiler setpoint, a temperature offset) -
sensor
(for all relevant products including the Smile P1) -
select
(for changing a thermostat schedule, a regulation mode (Adam only)) -
switch
(for Plugs connected to Adam, or Circles and Stealths connected to a Stretch)
Pre-requisites
The Plugwise Smile(s) in your network will be automatically discovered and shown on the integrations dashboard. All you need is the Smile ID as its password, which is an 8-character string printed on the sticker on the bottom of your Smile. Repeat this for each individual Smile.
Configuration
To add the Plugwise hub to your Home Assistant instance, use this My button:
Plugwise can be auto-discovered by Home Assistant. If an instance was found, it will be shown as Discovered. You can then set it up right away.
Manual configuration steps
If it wasn’t discovered automatically, don’t worry! You can set up a manual integration entry:
-
Browse to your Home Assistant instance.
-
In the bottom right corner, select the
Add Integration button. -
From the list, select Plugwise.
-
Follow the instructions on screen to complete the setup.
The hostname or IP address of your Smile. For example: 192.168.1.25
. You can find it in your router or in the Plugwise app using the Settings icon (☰) -> System -> Network. If you are looking for a different device in the Plugwise App, on the main screen first select Gateways -> the Smile of your choice, and then follow the previous instruction. Normally, the Smile(s) are automatically discovered, and you don’t have to provide the hostname or IP address.
Further configuration
For a thermostat, the active schedule can be deactivated or reactivated via the climate card. Please note, that when no schedule is active, one must first be activated in the Plugwise App. Once that has been done, the Plugwise Integration can manage future operations.
Auto means the schedule is active, and Heat means it’s not active. The active thermostat schedule can be changed via the connected thermostat select entity. Please note that only schedules with two or more schedule points will be shown as select options.
Entities
This integration will show all Plugwise devices (like hardware devices, multi-thermostat climate-zones, and virtual switchgroups) present in your Plugwise configuration. In addition, you will see a Gateway device representing your central Plugwise gateway (i.e., the Smile Anna, Smile P1, Adam or Stretch).
For example, if you have an Adam setup with a Lisa named ‘Living’ and a Tom named ‘Bathroom’, these will show up as individual devices. The heating/cooling device connected to your Smile will be shown as ‘OpenTherm’ or ‘OnOff’, depending on how the Smile communicates with the device. If you have Plugs (as in, pluggable switches connecting to an Adam) those will be shown as devices as well.
Under each device there will be entities shown like binary_sensors, sensors, etc. depending on the capabilities of the device: for instance centralized measurements such as ‘power’ for a P1, ‘outdoor_temperature’ on Anna or Adam will be assigned to your gateway device. Heating/cooling device measurements such as ‘boiler_temperature’ will be assigned to the OpenTherm/OnOff device.
Data updates
The interval which the integration fetches data from the Smile depends on the device:
- Power entities, such as the P1, will be refreshed every 10 seconds.
- Climate entities will be refreshed every 60 seconds.
- Stretch entities will be refreshed every 60 seconds.
Removing the integration
This integration follows standard integration removal. No extra steps are required within Home Assistant or on your Plugwise devices.
To remove an integration instance from Home Assistant
- Go to Settings > Devices & services and select the integration card.
- From the list of devices, select the integration instance you want to remove.
- Next to the entry, select the three-dot
menu. Then, select Delete.
This will also remove all connected Adam devices (such as Anna, Tom or Lisa) or connected Adam/Stretch plugs.
Actions
Update Smile data
Forced update of data from your Smile can be triggered by calling the generic homeassistant.update_entity
action with your Smile entity as the target.
# Example script change the temperature
script:
force_adam_update:
sequence:
- action: homeassistant.update_entity
target:
entity_id: climate.living_room
Reboot the Plugwise gateway
action: button.press
# Example script change the thermostat schedule
script:
reboot_gateway:
sequence:
- action: button.press
target:
entity_id: button.adam_reboot
Set HVAC mode
action: climate.set_hvac_mode
Available options include off
(Adam only) auto
, cool
, heat
, and heat_cool
(Anna with Elga only).
The meaning of off
is that the Adam regulation is set to off. This means that the connected HVAC-system does not heat or cool, only the domestic hot water heating function, when available, is active.
The meaning of cool
or heat
is that there is no schedule active. For example, if the system is manually set to cooling- or heating-mode, the system will be active if the room temperature is above/below the thermostat setpoint.
The meaning of heat/cool
is that there is no schedule active. For example, if the system is in automatic cooling- or heating-mode, the active preset or manually set temperature is used to control the HVAC system.
The meaning of auto
is that a schedule is active and the thermostat will change presets/setpoints accordingly.
The last schedule that was active is determined the same way long-tapping the top of Anna works.
Example:
# Example script climate.set_hvac_mode to auto = schedule active
script:
lisa_reactivate_last_schedule:
sequence:
- action: climate.set_hvac_mode
target:
entity_id: climate.living_room
data:
hvac_mode: auto
Turn on / turn off
action: climate.turn_off
, climate.turn_on
(Adam only)
These actions will switch the Adam regulation mode (= HVAC system mode) to off or on, affecting the operation of all connected thermostats.
climate.turn_on
will activate the previously selected heating or cooling mode.
Example:
# Example script climate.turn_off
script:
turn_heating_on:
sequence:
- action: climate.turn_off
target:
entity_id: climate.bios
Change climate schedule
action: select.select_option
# Example script change the thermostat schedule
script:
lisa_change_schedule:
sequence:
- action: select.select_option
target:
entity_id: select.bios_thermostat_schedule
data:
option: "Regulier"
Change boiler setpoint
action: number.set_value
# Example script change the boiler setpoint
script:
change_max_boiler_tempeture_setpoint:
sequence:
- action: number.set_value
target:
entity_id: number.opentherm_max_boiler_temperature_setpoint
data:
value: 60
Set temperature
action: climate.set_temperature
Example:
# Example script change the temperature
script:
anna_set_predefined_temperature:
sequence:
- action: climate.set_temperature
target:
entity_id: climate.anna
data:
temperature: 19.5
Set preset mode
action: climate.set_preset_mode
Available options include: home
, vacation
(Anna only), no_frost
, asleep
& away
.
Example:
# Example script changing the active (or currently set by schedule) preset
script:
anna_activate_preset_asleep:
sequence:
- action: climate.set_preset_mode
data:
preset_mode: asleep
Supported devices
The current implementation of the Python module (Plugwise-Smile) includes:
Adam (zone_control) with On/Off, OpenTherm, and Loria/Thermastage heating and cooling support:
-
v3.x
-
v2.3
-
Devices supported are Anna, Lisa, Jip, Floor, Tom, Plug, Aqara Smart Plug, and Koen (a Koen always comes with a Plug, the active part)
Anna (thermostat) with OnOff, OpenTherm heating, and Elga and Loria/Thermastage with heating and cooling support:
- v4.x
- v3.x
- v1.x
On the Elga, the cooling-mode can only be turned on, or off, via a switch present on the device, not via a toggle in the Plugwise App. Please make sure to reload the Plugwise integration after the cooling-mode-switch is turned off after being on, or the other way around. This will ensure that the Plugwise integration is being adapted to the change in function of the Elga.
Smile P1 (DSMR):
- v4.x
- v3.x
- v2.x
Stretch (power switches):
- v3.x
- v2.x